Film, Paper, Packaging, Board Testing Instruments in India

HEAT SEALER.
ASTM D-2673, D-4635, F-88

The sealer is versatile tool to find the ability of Heat Seal of packaging materials.

TECHNICAL SPECIFICATIONS

Sealer surface	225 x 20 (Approx.), Teflon coated
Temperature Range	Ambient to 250°C
Temperature Control	By digital Indicator-cum-Controller

STIFFNESS TEST APPARATUS (CANTILEVER BEAM TYPE)
ASTM D:747, D:5342, BS:2782, TAPPI T-489, JIS P: 8125

The apparatus converts the determination of the stiffness of plastics/paper by means of a cantilever beam. It is well suited for determining relative flexibility over a wide range.

The apparatus consisting essentially of the following :

Vise – A specimen vies, to which the pointer indicator is attached and which is capable of uniform clockwise rotation at a normal rater of 60 o of arc per min.
Weighing System – A pendulum weighing system, including an angular deflection scale, pointer indicator, bending plate of contacting the free end of the specimen and a series of detachable weights. This system shall be rotated as nearly frictionless rotation.
Load Scale – A fixed scale that measures the load a function of the deflection of the load pendulum system.
Angular Deflection Scale – The angular deflection scale shall be calibrated in degrees of arc and shall indicate the angle through which the rotating vise has been turned relative to the pendulum system.

Working on 220 Volt, AC, 50 Hz, 1 Ph.

DIGITAL OPACITY (TRANSMITTTENCE) TESTER
ASTM D: 1746, D: 4397, D: 2103

The instruments consist of:

Power supply stabilizer and an electric lamp.
Photo-electric detector-amplifier.
The meter unit digital readout, Range 0 – 100.0%

IMPACT RESISTANCE TESTER (DART IMPACT TE3STER) AS PER IS: 2508 & 10889, ASTM D-1709, D-3981, D-4635, D-4397, D-2103, IS-7765
The apparatus consists mainly of following parts: Vacuum Clamp System Electromagnet Dart. DO BUT WITH PRESSURE CLAMP ARRANGEMENT INSTEAD OF VACUUM CLAMP AND WITHOUT AIR PREESURE SYSTEM.

THICKNESS GAUGE (DEAD WEIGHT TYPE) ASP PER IS-2508, 6193, 5351, ASTM D-2103, D-3981, D-4635
The Thickness Gauge for Film is a dead load type bench thickness gauge. The consists of a dial gauge type micrometer and a flat pressure foot, which exerts a specified load on an anvil.

DIGITAL COEFFICIENT OF FRICTION TESTER
ASTM D-1894, IS: 2508, ASTM D-2103, D-2673, D-3981, D-4635, D-5047, BS: 2782, DIN: 53375, ISO: 8295

The coefficient of friction is the ratio of the frictional resistance to the normal pressure acting on two faces in contact. This coefficient of friction is the inverse measure of the relative easy with which one surface moves over surface of another.

SCUB RESISTANCE TESTER OF PRINT MATERIALS (RUB RESISTANCE TESTER)
AS PER BS: 3110

The apparatus gives an idea of rub resistance of rubbing of the printed surface.

BOND / HEAT SEAL STRENGHT TESTER

The tester consists of a Electro-mechanical loading system and load-cell with digital indicator.

Capacity : 2000 Gsm. Or 5000 Gms.

*HIGHER LOAD CAPACITY AND DIFFERENT SPEED OF TESTING WILL BE QUOTED SEPARATLY.

WATER VAPOUR TRANSMISSION TEST CHAMBER AS PER IS : 1060 (P-II) & ASTM E-96

TECHNICAL SPECIFICATIONS
It can be maintained as per ASTM
Temperature	20°C or 32.2°C or 37.8°C
Humidity	50% or 90%
As per ISI
Temperature	27°C or 38°C
Humidity	65% or 90%
Operation on 220/230 Volts, Ac. Single Phase, 50 Cyls. Mains
Size	18” x 18” x 18”
ESSENTIAL ACCESSORIES FOR W.V.T
Test Dish
Waxing Template
Cutting Template

ROLLING BALL TACK TESTER
AS PER ASTM D-3121/94

The rolling ball tack test is fast, easy to run and little operator training. This test is intended primarily for quality control use since it demonstrates good reproducibility within a single laborator and ability to detect batch to batch variations accurately if adhesives film thickness is held constant.

The tester measures the comparative tack of pressure sensitive adhesives by a rolling ball and most appropriate for low-tack adhesives.

ELMONDORF TEARING TESTER. AS PER IS :1060,ASTM D 1922&689
For determining Tearing Strength of film, Paper, Packaging, pulm, Rubber, Celluloid Cloth Tape etc.

HAZE METER. AS PER IS:2508 & ASTM D-1003
This method is intended to measure the light-transmitting properties and form these, the light-scattering properties of planner sections of transparent plastics. Complete with electronic voltage stabrilizer and operating on 220/230 voltage, single phase, 50 cycles, A.C. Mains.

DIGITAL GLOSS METER
AS PER IS :101 , ASTM D-2475, IS:1060, 2508, ASTM D-523, 1222, 1223, C-346.

Gloss Meter is designed to confirm to the requirements of different standards above and can measure specula gloss of surfaces. Gloss meter can be used for quality control of the gloss of paints, porcelain, ceramics, plastics, opaque glasses and any other glossy surfaces and also the whiteness of a wide range of materials like Paper, Cloth, Floors, Pigments, Powder etc.
Complete with master standard and one head.

Technical Specification
Digital Indication	99.9
Accuracy	better than 1%
Head	20° / 57.5° / 60° / 85° / 75°
Power	1 Ph. 220 Volt, AC, 50 Hz.

WHEEL ABRADER (TABER TYPE)
ISO:9352, BS:2782, ASTM D:1044, D:1175, TAPPI T476, ASTM C-501

The abrader consists of a motor-driven rotating disc on which specimen is fixed. A pair of abrasive wheel is allowed to turn freely on their axis and applied to the test specimen at a specified position under a specified load.

TECHNICAL SPECIMENS

Specimen dimension	100 mm dia / octagonal by
Grinding wheel dimensions	51.6 mm 0 x 12.7 mm (2 x ½ in.)
Test speed	60 rpm.
Test load	250, 500, 1000 gm
Counter	6 digital, digital, preset
Type of grinding wheel	H22
Power source	220/240 Volt, AC, 50 Hz, 1 Ph

BURSTING STRENGHT TESTER MOTOR DRIVEN
DOUBLE RANGE : 7/35 Kg/Cm AS PER IS: 1060, ASTM D-774

This operates on the uniform pressure distribution principle of hydraulics to accurately determine the bursting strength of sheet materials. The tester is most widely used for testing Paper, Corrugated and solid fiber boards sheets and textile materials. The machine is supplied with a bottle of hydraulic fluid 200 cc. and SFM-117A. With digital indication.

SFM-117B. With Pneumatic System and Digital Indication

Film, Paper, Packaging, Board Testing Instruments in India

Our Latest Products